How to Make a Plain Roman Blind

How to Make a Plain Roman Blind

 ·  Cut the fabric to the required size adding 2” (5 cms) to the width for side seam allowances and 2" (5 cms) to the length for hem allowances. If more than 1 width of fabric is required, join widths together with a flat seam. Make sure there is a full width in the centre with equal part widths added at each side. If patterned fabric is used, match the pattern across all the widths.

·  Cut out the lining to exactly the same measurements as the top fabric, omitting any extra allowance for pattern matching.

·  Lay fabric on a flat surface, right side up.

·  Lay the lining on top, wrong side up, matching the raw edges. Smooth out all the wrinkles and creases from the two fabrics and pin them together.

·  Pin and stitch down both sides and along the bottom edges, 1" (2.5cms) in from the raw edges.

·  Trim the 2 bottom corners and make a second row of stitches across the bottom, 0.25” (6 mm) in from the raw edge. Insert a dowel into the channel between the 2 rows of stitches.


· Remove all the pins and turn the blind the right side out.

·  Press the blind, taking care to press out and flatten the seams.

·  Lay the blind on a flat surface, lining side up, and pin the two layers together all over.

·  Draw a pencil line across the width of the blind, 2" (5 cms) down from the top raw edge.

·  Divide the rest of the length into equal sections of between 8" and 12" (20 and 30cms) with a half section at the bottom edge and mark.

·  Draw pencil lines across the blind at these marks. All these lines should be parallel to the top edge and at right angles to the sides. These will be the sewing lines for the pockets.

·  To make up the pockets to hold the dowels, cut strips of lining fabric 3" (7.5 cms) wide and as long as the blind is wide. If possible, cut these strips from the length of the fabric rather than across the width as the weave is tighter and the pockets will wear better. Cut 1 strip for each whole pleat.

·  Fold each strip in half width ways, right sides together and matching the raw edges.

·  Machine stitch across 1 end and down the length 0.5" (12mm) in from the raw edges.

·  Turn right side out and press.

·  Pin the folded side of the pockets to the pencil lines, 0.5" (12 mm) above the marked lines with the ends of the pockets 0.5" (12mm) in from each side of the blind.

·  Sew the pockets to the blind along the marked lines.

·  The machine stitching should be as unobtrusive as possible on the front of the blind.

·  Slide a length of wooden dowelling into each pocket and oversew the open ends.

·  Hand sew the plastic rings to the outer edges of the pockets. These should be positioned in rows down the length of the blind, 2" (5 cms) in from each side edge and between 8" to 16" (20 to 40cms) intervals evenly across the blind.

·  Turn down 1" (2.5 cms) to the wrong side, at the top edge and press.

·  Pin and stitch the “sew” side of the Velcro across the top of the blind, on the wrong side, close to the fold. Stitch both sides in the same direction to avoid puckering.

·  Hang the blind by pressing the 2 sides of the Velcro together.

·  Screw an eyelet into the underside of the batten directly above each line of rings on the blind and 1 at the end of the batten to the side that the blind will be operated from.

·  Cut the nylon cord into 3 and knot 1 length to each bottom ring. Thread the cords up through the line of rings and through the eyes on the batten taking all 3 cords to 1 side of the window.

·  Trim the ends of the cords level, thread them through the acorn and knot to secure.

·  Position a cleat at a convenient height at the side of the window and fix in place.

·  Pull up the blind, winding the cords round the cleat in a figure of 8 to hold it in place.