How to Sew and Make New
Curtains
Here is a good lesson to learn an indoor DIY project: how to make new curtains.
The carrying out is not difficult; if you can sew a straight line with a
machine, you can make new curtains to slide over your windows. The challenge is
in the planning.
Fabric
A medium-weight drapery fabric is a good choice; it is often wider than
dress material. Avoid large designs. They
can be overwhelming in a small space, and you will need extra fabric to allow
matching. Avoid dark colors, too, as they are prone to fading. Your curtains
will last longer and offer more privacy if they are lined. Laminated fabric is
hard to find, but drapery lining is widely available and can be sewn to your
curtain fabric. Look for a medium weight lining that provides some sun and thermal
protection. You also need a roll of "stay tape" (to stabilize the
stretchy diagonal edges of the corner curtains), about 12” of sticky-back white
fuzzy (loop) Velcro, and 12” of sew-on hook-side Velcro. These items are
available from fabric stores.
Hardware
For curtains that slide on a track, you need to purchase "glide
tape" (which is sewn to the curtain) and "white wall track"
(which is screwed to the wall). The standard tape package contains 72" of tape, and the
track comes in lengths that vary around 45", depending on vendor. These supplies
are not expensive, but since you have to pay shipping, be sure to order enough
the first time. If you already have the sliding track system, order new tape.
The plastic buttons become brittle with age and it's time-consuming to remove
old tape. At most hardware stores, you can buy finishing washers for tiebacks) and
decorative screw caps. Screws should be fully threaded, with no smooth shank,
and stainless steel is best. Use an awl or ice for putting holes in the fabric
and Velcro, and for starting screw holes in the wall.
Measuring
Length:
The finished curtains on the A walls
should all hang to the same distance above the hinge. Allow enough coverage at the top of the window
for the wall track. Width: In order for the curtain panel to clip into
the end of the wall track, and cover the hardware, the side edges of the
curtain should extend 1" beyond a glide-tape button.
Hold the glide tape above the window to determine this minimum width.
The measurement will be wider than the actual window. Measure all the windows, including
the door. Add at least 2" to each width dimension to allow for seams. Curtains
should always be cut lengthwise on the raw fabric, matching the fabric design, or
they won't hang properly.
Corner curtains require special attention, noted here
in italics. If your fabric has a printed pattern, you cannot create matching triangles
by cutting a square in half – if you do, one triangle will be upside down!
Matching triangles on a single wall must be cut as vertical, mirror-image twins.
NOTE: If your corner windows are the usual 21” high, and you want your finished
curtain to have two equal legs of about 32”, those raw cut edges must be at
least 33 ¾”, NOT 33”, or you have no seam allowance for the diagonal.
The surest method is to make a paper pattern for your corner, pin it to the
fabric, and cut ½” from the edges all the way around.
Knowing the width of your fabric, figure how many yards you will need
for your project. Make a similar calculation for the lining, which may be
manufactured in a different width. To confirm your calculations, sketch your
layout on graph paper. You will also need fabric to make tie-backs for your
curtains. These 4” strips can be cut horizontally. Remember to allow extra
fabric for all seams and hems.
How to Sew and Make New Curtains |
Construction: The easiest way to line your curtains
is to cut mirror-image pieces of fabric and lining, adding ½” seam allowance
all the way around. Pin the right sides together and stitch ½” from the
edge all around, leaving about 6” unstitched. Trim excess material from the
corners and turn the piece inside out through the unstitched pocket. Use the
scissor points to gently poke the corners into shape. Press the edges carefully,
fingering the unstitched pocket into place. Top stitch around the entire panel,
including the unstitched pocket, about ¼” from the edge. Press again. Place the
glide tape along the top of the back of the curtain panel, with the end glide
buttons about 1" inside each side. Stitch the top of the glide tape to the
back of the top of the curtain panel, sewing along the top stitching. Use a zipper
foot on the machine so that you can sew close to the glide buttons.
Finally, stitch the bottom edge of the glide tape in place. If you are
using glide tape on both top and bottom of a curtain, as you would for the roof
bubbles, make certain that the upper and lower buttons are directly opposite each
other so that the open curtain pleats evenly.
Add a piece of sew-on Velcro to the back of any curtain hem or corner that
you want held against the wall.
The panels for the corner windows are right-angle triangles.
While construction is basically the same as for the rectangular curtains, the
stretchy diagonal edges need special care. When you pin the lining for sewing,
include a strip of Stay Tape along the diagonal sewing line and stitch it into
the seam. The narrowest (bottom) point of the triangle will be thick and needs
careful trimming to remove extra bulk before it’s turned inside-out. The large
curtain next to the door may have one triangular side. This area can be cut
separately, then sewed to the rectangle as part of the whole curtain.
Tiebacks: Cut tieback strips 4” wide and 1" longer
than the finished length. Fold the strip in half lengthwise, right sides
together, and stitch ¼” from the long edge. Press the seam open and turn the
strip inside-out. Center the seam and press again, turning ½” of the raw ends
inside. Top stitch all the way around, ¼” from the edge. Sew a square of loop-side
Velcro to one end, over the long seam.
Mounting
Glide Track:
The plastic track can be cut
to length with utility shears. If in doubt, cut it long and shorten it as
needed. Mark the screw holes by holding the track, with curtain attached, at
the desired location. Put a screw near each end of the track.
Fixed corner triangles: Use masking tape to hold the curtain in place.
Through the diagonal curtain edge, screw 4 small pan-head screws in decorative
covers.
Tiebacks: Through the non-Velcro end of each tieback, seam-side
up, screw a short pan-head screw and finishing washer, hiding the screw behind
the curtain.
Velcro: After the curtains
and tiebacks are in place, press the fuzzy side of sticky-back Velcro to each
piece of sewn-on loop Velcro. Stick it against the wall where desired, pull
away the curtain, and screw each sticky-back Velcro in place with a short,
small flat-headed screw.